Login
Register
434-738-8647
Home
My Account
About Us
Contact Us
Blog
Events
Shopping Cart
0
Free shipping for all orders over $100
0
Items
Toggle navigation
Helicopters
Parts
Align
Mikado
MSH Protos
OMP Hobby
OXY
SAB Goblin
Synergy
XL Power
Lynx Upgrades
Canopies
Bearings
Blades
Electronics
ESC's and BEC's
Batteries
Flybarless
Charging
Servos
Regulators
Motors
Nitros
Radios
Accessories
Electric Accessories
Simulators
Setup and Repair Equipment
Storage and Transport
Apparel
Home
Radios
Jeti Simulator Interface Cable for DS/DC Transmitters - RF
Jeti Simulator Interface Cable for DS/DC Transmitters - RF
Jeti Simulator Interface Cable for DS/DC Transmitters - RF
Part Number:
ESMCAB1
Write a Review
On sale:
$9.00
$7.00
Jeti Simulator Interface Cable for DS/DC Transmitters - RF
Availability:
Out of Stock.
Put me on the Waiting List
Put me on the Waiting List
Description
These interface cables allow you to connect a Jeti receiver to your flight simulator. With this setup you can now use your Jeti transmitter to wirelessly control your flight simulator. Select the square connector to interface with traditional RealFlight.Select the round connector to interface with either RealFlight Wired Interface or PhoenixNeeded Equipment:(1) Jeti Duplex Transmitter(1) Jeti Receiver with Rx Battery Pack or Other Power Supply(1) Simulator Interface CableStep by Step Instructions:Step 1: Set up a simulator model(s) in your Jeti radioStep 2: Bind a receiver to that modelStep 3: Depending on your Simulator set your receiverÕs output to PPM Positive or PPM NegativeStep 4: Set the "output period" for the PPM output channel of your Jeti receiver to 20msStep 5: Connect the interface cable to the PPM output channel of your Jeti receiver and to your simulatorÕs interfaceStep 6: Power your receiverStep 7: In your simulator, reassign the control channels as neededStep 1:Bind your receiver to the transmitter. With the receiver powered go to Main Menu on your radio and select Model. In the Model menu, go to Device Explorer. Once in Device Explorer, click on your receiver. Change the Serial Link to PPM Positive. Step 2:Connect Simulator Interface Cable to the appropriate port on your receiver for PPM output. Connect the other end of the cable to the back of the Interlink Transmitter (Included with Simulator). Make sure that you have plugged the simulator interface cable into the appropriate port on the receiver and that the battery is plugged into an open port on the receiver other than the EXT port. Step 3:Run Realflight and under Simulation, click on Select Controller. Choose JR in the bottom box and click on edit to create a profile. Make sure to create separate profiles for helicopters and airplanes in both the software and in the radio. The profile in the software should look like this for the Airplane!!! The profile in the radio should look like this for the Airplane!!! The profile in the software should look like this for the Helicopter!!! The profile in the radio should look like this for the Helicopter!!! Make sure that when setting up the radio in the simulator software, the box labeled "Enable Software Radio Mixes," is not checked. This will allow you to set up your radio as you would normally for flying. This includes things like idle up and throttle hold for helicopter and dual rates/exponential for airplanes. If you have followed these directions, you should now be able to fly your simulator using your Jeti DS/DC transmitter.
Reward Points
21 points will be rewarded to you when you buy this item.
Related Items
Quick View
Futaba Neck Strap - Red
Out of Stock.
$16.59
Add To Cart
Quick View
Spektrum Air Telemetry Flight Pack Voltage Deans
In Stock.
$18.59
Add To Cart
Quick View
Spektrum Aircraft Telemetry GPS Sensor
Out of Stock.
$99.99
Add To Cart
Quick View
Jeti Telemetry Sensor Li-Poly Battery MULi 6s EX
Out of Stock.
$45.00
$38.00
Sale
Add To Cart
Quick View
Mikado Sensor Connection Wire 150mm, Vbar Control
In Stock.
$7.00
Add To Cart
Quick View
Mikado 3 Position Switch (Short), Vbar Control
In Stock.
$19.00
Add To Cart
Quick View
Mikado Vbar Control/Scorpion ESC-Cable, 350mm
In Stock.
$10.00
Add To Cart
Quick View
Futaba R7003SB (FASSTest/S.Bus2) Receiver
Out of Stock.
$100.00
Add To Cart
Quick View
Futaba R3008SB T-FHSS Telemetry System 8 Channel S.Bus Receiver
Out of Stock.
$70.00
Add To Cart
Quick View
Futaba 16IZ Heli Transmitter without receiver
In Stock.
$650.00
Add To Cart
Menu Links
Categories
×
Store Search